Welcome to Cables on Sale!

Your Shopping cart is empty.

Skip to Main Content »

Monoprice HDMI® Over CAT5E / CAT6 Extender Wall Plate w/ LED Indicator (Pair) - Single Port (1P) - White

    • The product Wallet Case Cover for Samsung GALAXY S2 i9100 has been added to comparison list.

Details

Extend the range of your High Speed HDMI® signal and keep the wiring hidden safely within your walls using this HDMI Wall Plate Extender!

The HDMI Wall Plate Extenders use Cat5e or Cat6 network cables to transmit the HDMI audio-video signal over distances greater than the 25 foot maximum certified for High Speed signals using HDMI cables alone. To use them you need to run two Cat5e/6 cables through the walls. Note that these must be CL2 rated for in-wall use and must be wired to the EIA/TIA-568B standard.

Next you plug the ends of each cable into the backs of the wall plates. Make sure that the wall plate labeled "HDMI IN" is at the source side and the one labeled "HDMI OUT" is at the destination end. Once the cables are inserted into the wall plates, screw in the cable bridges to make sure they do not disconnect or come loose.

Tip: The Cat5e/6 cables need to be plugged into the appropriate jack on the back of the wallplate, labeled 1 and 2. To make it easier to identify which cable is which, it is recommended that you use different colored cables. So, for example, the Red cable would be Cable 1 and the Green cable would be Cable 2.

Now, install the Wall Plates into a single-gang, low voltage mounting bracket (not included) in the wall and install the faceplates. Your extender is now ready for use! Simply plug the output of your source device (e.g., AV Receiver, Blu-Ray player, etc.) into the HDMI IN jack and plug the TV in your remote room into the HDMI OUT jack.

Under most circumstances the system will draw all necessary power from the HDMI cable itself. If you have signal reliability issues, you may need to plug a 5 VDC AC adapter into one or both of the wall plates to provide necessary power. Alternatively, you can hardwire a 5 VDC AC adapter into the back of the remote wall plate (labeled HDMI OUT), with the positive wire connected to the + and the negative wire connected to the - connection.

Note: Monoprice strongly recommends the use of minimum 24 AWG HDMI cables when connecting a device, such as this extender, between the source and destination devices to ensure minimal signal loss and maximum High Speed signal reliability.

Note: Although this extender will work with Cat5e UTP cables, Monoprice STRONGLY recommends using Cat6 STP cabling for anything longer than minimal distances. Cat6 STP cabling will provide the highest reliability and signal integrity to ensure that your installation is trouble-free under all conditions for years to come.

Note: The 5 VDC power jacks on the front of each wall plate are "standard" cylindrical DC power jacks with a 2.1 mm pin diameter.

Features:

Extends HDMI 1080p signals reliably up to 30 meters (90 feet)

Automatic adjustment of feedback, equalization, and amplification

Powered by the HDMI cable in most installations

Optional 5 VDC power input for the rare cases when self-power is insufficient for a reliably signal

Conforms to North American wall plate standard

Can use Cat5e or Cat6, UTP or STP cabling

Supports HDMI resolutions up to 1080p with 12-bit color depth

Supports high resolution audio, including DTS-HD Master Audio™ and Dolby True-HD™

Support Files:

User's Manual (Aug 1, 2011)

HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

DTS is a registered trademark and the DTS logos, Symbol, DTS-HD and DTS-HD Master Audio are trademarks of DTS, Inc.

Dolby and the double-D symbol are registered trademarks of Dolby Laboratories.

Specifications

Supported Video Resolutions 480i, 576i, 480p, 576p, 720p, 1080i, 1080p

Supported Audio Formats DTS-HD Master Audio™, Dolby TrueHD™, etc.

Transmission Distances 1080i 8-bit to 50m, 1080p 8-bit to 30m, 1080p 12-bit to 25m

Minimum Cable Requirements Cat5e UTP 24 AWG Solid

Recommended Cable Requirements Cat6 STP 23 AWG Solid

Operating Temperature Range -5 to +35° C (-41 to +95° F)

Operating Humidity Range 5 to 90% RH (No condensation)

Input Video Signal 0.5 to 1.0 volts p-p

Input DDC Signal 5 volts p-p (TTL)

Power Consumption 3 watts maximum

Physical Dimensions (LxWxH) 115 x 70 x 35 mm

Net Weight 150 gm / pair

Included in the Box:

1x HDMI® transmitter wall plate

1x HDMI® receiver wall plate

2x Faceplates

4x Faceplate screws

2x Cable locking bridges

2x Locking bridge screws

Question: The picture passing through the extender is constantly flickering or on occasion getting video and audio cutout, what can I do?

Answer: We would recommend to try to run the setup outside the wall just to test. A electrical wire or video cable if inside the wall can cause interference causing flickering or video and audio signal loss. Try rerouting cable paths and distancing devices from sources of interference, such as moving the electrical and other cables away from cables in wall.

Also please test another source device with the extender if using a DVD player try a cable box for example and to also try a different video resolution if trying 1080p try 720 just to test the connectivity.

Additional Information

SKU 8200 - S4-45
Length (ft) No
Color No
Gauge No

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.